• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to repair ignition lock cylinder (This Webpage) an Ignition Lock Cylinder

If your car's keys will not turn, it's time change the ignition lock cylinder. The lock cylinder is a mechanical tumbler that your key ignition replacement can slide into, as opposed to the switch which is an electrical part of the ignition system.

Over time, "wafers" can break or become worn out. The use of WD-40 or graphite can temporarily fix the problem, but replacement is the only way to fix it permanently.

Removal of the steering column

Modern cars do not use steering column locks. They use keys to start the car by pressing and turning an electronic switch located in the dash panel. This modern system works better and is much simpler than the old lock-cylinder method. However, there are older vehicles that utilize the traditional ignition lock cylinder. If this part fails, you may need to replace it in order to start the vehicle. This isn't a task for the novice and is best left to a professional.

Utilizing a screwdriver, you can remove the fasteners that hold the trim panels that surround the upper and lower steering column. This will allow you access to the area surrounding the steering column.

You will find an Allen head bolt on the side of the steering wheel that is closest to the driver. This bolt holds the unit for the wiper/signal unit in position. Remove this bolt and place it aside. Depending on your car's year you might find three or four small screws with flat heads, which hold the plastic over the turn-signal switch in place. Take these screws off and put them aside.

To get to the lock cylinder, you will need to remove the wiper/signal assembly. This will require the use of a specially designed tool, or you could to do it using a piece of metal like a cold chisel. A locksmith will also be able to use the shear bolt removal kit.

If you're unable to insert the key into the ignition switch, the lock cylinder may be stuck. You can either call locksmiths or insert the key into the ignition switch and move it to the ACC to release the pin of the lock cylinder.

A locksmith can employ the shear tool to remove the lock cylinder, or they can make use of a torch to cut the pin and then shave the pin down to remove it. They can re-key the ignition cylinder to ensure it matches the keys you already have. This will save you money on the purchase of a new ignition.

Replace the Ignition Cylinder

The ignition Cylinder is a cylindrical mechanical component which houses and locks the key of your car. The cylinder is fitted to the key and "reads" the anti-theft code to allow or denial of the starting of your vehicle. The cylinder can wear down over time. It may also become bent or broken. In this instance you'll need replace the cylinder to get your car ignition key replacement running.

The signs of a damaged or worn cylinder can be seen in problems with turning your key, or the ignition switch not moving to the ACC or RUN position, or a warning light appearing on the dash. If you have a spare, try using it in the lock. You may be able use graphite or WD-40 to adjust the cylinder's settings, however, this is only for a short period of time.

If you've got a new key to replace the ignition cylinder and follow the instructions above to install it. Install the new ignition cylinder by making sure it's securely seated into the steering-column tube flange and aligned to the keyway on the shroud. If you're unsure about the correct alignment of the cylinder, check your car's repair manual or an automotive expert.

Once the cylinder is in, turn the key to the ACC or RUN position. You should hear a click confirm that the ignition switch is fully seated in the cylinder. If your car has an anti-theft device, you will have to perform the anti theft relearn procedure to programme the new ignition cylinder into your key.

Some experts suggest hiring a professional to replace your ignition cylinder. This is due to the fact that it's often necessary to disable the airbag in the steering column for access to the cylinder. Additionally, the replacement is likely to involve removing and replacing the ignition and steering wheel covers. This is why you should let a mechanic with experience. They'll be able remove the cover for the steering column and then properly install a new ignition lock cylinder in your vehicle. They'll also be able to verify that the ignition lock cylinder is programmed by your key and that it will start correctly when you insert it.

Installing the Ignition Cylinder

Although ignition lock cylinders are becoming less important in modern vehicles because of advancements in push-to-start and remote start systems, they're common on older cars. If you're having trouble starting your car or the ignition switch is stuck, it could be a defective ignition cylinder. It's relatively simple to replace the ignition lock cylinder, and then fix the issue.

The ignition cylinder is the mechanical portion of the system that is inserted into the ignition switch of your car and sends power to the rest of the engine. The ignition switch and ignition cylinder are two distinct components. The switch is an electronic component that connects with the computer in your car to send signals to start the engine when you turn the ignition key.

The pins on the cylinders of ignition locks move upwards and downwards, allowing your key to move and rotate within the cylinder. Each movement of the cylinder and the key creates a tiny friction that keeps the key in place, but over time, these small movements can cause the wafer tumblers to wear down. If the tumblers get worn out and the key is no longer able to slide into the cylinder, it will not be able slide into the cylinder or rotate it.

The first sign of trouble is usually a worn out ignition coil that is found in the majority of automobiles. However, the key may become stuck and become difficult to insert or remove from the ignition cylinder. These are indications that you should replace your ignition lock cylinder as soon as possible.

Replacing the ignition cylinder on your vehicle isn't difficult, but it's a job that should be completed by a skilled do-it-yourselfer only when you're confident enough to follow the proper procedure for your specific brand and model of vehicle. You can complete the task quickly and accurately with a complete repair manual for your vehicle. If you're not confident installing the ignition cylinder on your own, you can have one of our ASE-certified mobile mechanics complete the work for you at a time and place.

Testing the Ignition Cylinder

The ignition lock cylinder is a mechanical part that is fitted to your key and permits it to rotate and start your vehicle. It's located inside the ignition switch, which locks the ignition and reads anti-theft coding to permit the key to turn. The cylinder that locks the ignition is prone to wear and may eventually fail, leading to issues powering your vehicle or making it difficult to insert and remove the key.

Some of the main indicators that your car's lock cylinder is about to fail is difficulty in starting it, or places where the key becomes stuck when you turn it. These problems are usually a sign that the cylinder must be replaced. In certain instances, you might even notice an alert light on your dashboard that indicates the possibility of a failure.

As the cylinder gets older it can be damaged by corrosion or wear and wear and. This can cause the pins and tumblers made of wafer to wear out, cause damage or even break, which could prevent your car's ignition from working. The ignition may still work in certain situations when you move it around. However this could be a sign that something is not right.

You can test your ignition cylinder to determine if it's worn out or if the key is bent or damaged. If you have a multimeter, you can back-probe the module's red wire connection and the battery terminal of the ignition coil to determine if there's the voltage. If you do not find any voltage, then the switch and module are likely to require replacement.

Replacing the ignition cylinder typically costs between $200 and $300, and it's usually best to have an expert mechanic do the task. The process is made more complicated by the fact that you could require removing other components to access the cylinder that controls ignition, including the steering column. Based on the vehicle you have, the replacement procedure can be accompanied by the need to disable the airbag system, and then you'll need to reprogramme your key to work with the new cylinder. This can be done at an authorized dealer however, you can also learn how to do it yourself with the proper tools and instructions.